Non-aqueous interfacial polymerization method by using alcoholic monomers such as 1,3,5- trihydroxybenzene (THB), 4-dihydroxybiphenyl (BPH), 4,4 dihydroxybenzophenone (DHBP) and Phos- phoric chloride trimer (HCCP) free-standing films were developed. Membranes on Polyacrylonitrile or PAN UF membrane as a support were created by performing interfacial polymerization (IP) between 3.5 weight percent HCCP in cyclohexane and 10 weight percent BPH, DHBP,THB, and other monomers in DMSO and Agnique in different samples by using the hydroxyl molar ratio 0.5, 0.75, and 1 of KOH or t-BuOK. Free-standing polymeric layers and thin film composite membranes were formed by using two different solvents (DMSO and Agnique) and two different base, KOH and tBuOk. FTIR spectroscopy in attenuated total reflectance mode (FTIR-ATR) was used to characterize the films, PAN membrane before and after treatment, and polyphosphazene TFC membranes. SEM was used to see the structure of PAN support before and after the treatment. thermal treatment of PAN support was done by a multistep method at 180, 230, and 280 C. The results show that PAN at 180 C was the most defect free one. Polyphosphazene (PPz) thin film composite membranes were produced by using an IP cell. SEM images of PPz demonstrate that samples are not defect free so more attempts needed to get a defect free PPz selective layer. Gas permeance setup was used to measure GPU of CO2 and N2 for the membranes. Results show us the membrane is not dense enough to play a barrier or sieving role for gas separation applications. Therefore, further investigation should be used to obtain a selective layer.

Non-aqueous interfacial polymerization method by using alcoholic monomers such as 1,3,5- trihydroxybenzene (THB), 4-dihydroxybiphenyl (BPH), 4,4 dihydroxybenzophenone (DHBP) and Phos- phoric chloride trimer (HCCP) free-standing films were developed. Membranes on Polyacrylonitrile or PAN UF membrane as a support were created by performing interfacial polymerization (IP) between 3.5 weight percent HCCP in cyclohexane and 10 weight percent BPH, DHBP,THB, and other monomers in DMSO and Agnique in different samples by using the hydroxyl molar ratio 0.5, 0.75, and 1 of KOH or t-BuOK. Free-standing polymeric layers and thin film composite membranes were formed by using two different solvents (DMSO and Agnique) and two different base, KOH and tBuOk. FTIR spectroscopy in attenuated total reflectance mode (FTIR-ATR) was used to characterize the films, PAN membrane before and after treatment, and polyphosphazene TFC membranes. SEM was used to see the structure of PAN support before and after the treatment. thermal treatment of PAN support was done by a multistep method at 180, 230, and 280 C. The results show that PAN at 180 C was the most defect free one. Polyphosphazene (PPz) thin film composite membranes were produced by using an IP cell. SEM images of PPz demonstrate that samples are not defect free so more attempts needed to get a defect free PPz selective layer. Gas permeance setup was used to measure GPU of CO2 and N2 for the membranes. Results show us the membrane is not dense enough to play a barrier or sieving role for gas separation applications. Therefore, further investigation should be used to obtain a selective layer.

Non-aqueous polyphosphazene interfacial polymerization membranes for gas separation applications

MEHMANDAAR OSKUEI, ERFAN
2025/2026

Abstract

Non-aqueous interfacial polymerization method by using alcoholic monomers such as 1,3,5- trihydroxybenzene (THB), 4-dihydroxybiphenyl (BPH), 4,4 dihydroxybenzophenone (DHBP) and Phos- phoric chloride trimer (HCCP) free-standing films were developed. Membranes on Polyacrylonitrile or PAN UF membrane as a support were created by performing interfacial polymerization (IP) between 3.5 weight percent HCCP in cyclohexane and 10 weight percent BPH, DHBP,THB, and other monomers in DMSO and Agnique in different samples by using the hydroxyl molar ratio 0.5, 0.75, and 1 of KOH or t-BuOK. Free-standing polymeric layers and thin film composite membranes were formed by using two different solvents (DMSO and Agnique) and two different base, KOH and tBuOk. FTIR spectroscopy in attenuated total reflectance mode (FTIR-ATR) was used to characterize the films, PAN membrane before and after treatment, and polyphosphazene TFC membranes. SEM was used to see the structure of PAN support before and after the treatment. thermal treatment of PAN support was done by a multistep method at 180, 230, and 280 C. The results show that PAN at 180 C was the most defect free one. Polyphosphazene (PPz) thin film composite membranes were produced by using an IP cell. SEM images of PPz demonstrate that samples are not defect free so more attempts needed to get a defect free PPz selective layer. Gas permeance setup was used to measure GPU of CO2 and N2 for the membranes. Results show us the membrane is not dense enough to play a barrier or sieving role for gas separation applications. Therefore, further investigation should be used to obtain a selective layer.
2025
Non-aqueous polyphosphazene interfacial polymerization membranes for gas separation applications
Non-aqueous interfacial polymerization method by using alcoholic monomers such as 1,3,5- trihydroxybenzene (THB), 4-dihydroxybiphenyl (BPH), 4,4 dihydroxybenzophenone (DHBP) and Phos- phoric chloride trimer (HCCP) free-standing films were developed. Membranes on Polyacrylonitrile or PAN UF membrane as a support were created by performing interfacial polymerization (IP) between 3.5 weight percent HCCP in cyclohexane and 10 weight percent BPH, DHBP,THB, and other monomers in DMSO and Agnique in different samples by using the hydroxyl molar ratio 0.5, 0.75, and 1 of KOH or t-BuOK. Free-standing polymeric layers and thin film composite membranes were formed by using two different solvents (DMSO and Agnique) and two different base, KOH and tBuOk. FTIR spectroscopy in attenuated total reflectance mode (FTIR-ATR) was used to characterize the films, PAN membrane before and after treatment, and polyphosphazene TFC membranes. SEM was used to see the structure of PAN support before and after the treatment. thermal treatment of PAN support was done by a multistep method at 180, 230, and 280 C. The results show that PAN at 180 C was the most defect free one. Polyphosphazene (PPz) thin film composite membranes were produced by using an IP cell. SEM images of PPz demonstrate that samples are not defect free so more attempts needed to get a defect free PPz selective layer. Gas permeance setup was used to measure GPU of CO2 and N2 for the membranes. Results show us the membrane is not dense enough to play a barrier or sieving role for gas separation applications. Therefore, further investigation should be used to obtain a selective layer.
Polyphosphazene
TFC membrane
Gas separation
File in questo prodotto:
File Dimensione Formato  
MEHMANDAAR OSKUEI ERFAN MASTER THESIS 2084319 (1).pdf

accesso aperto

Dimensione 21.14 MB
Formato Adobe PDF
21.14 MB Adobe PDF Visualizza/Apri

The text of this website © Università degli studi di Padova. Full Text are published under a non-exclusive license. Metadata are under a CC0 License

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/20.500.12608/116610